想问下保险有几种打法

烛雨

今天的面试时面试官问了我保险有几种打法，我只知道双线缠绕法。回去后查了下还有单线法。想问问前辈们还有没有其他的打法

xiaoqian123

有4种吧！

xiaoqian123

单线分两种，双线也分两种

烛雨

xiaoqian123 发表于 2017-9-21 10:35
单线分两种，双线也分两种

能具体说下分别是哪两种吗

xiaoqian123

烛雨 发表于 2017-9-21 10:44
能具体说下分别是哪两种吗

专业术语我也不知道怎么翻译过来

xiaoqian123

不知道这是不是你想要的

烛雨

xiaoqian123 发表于 2017-9-21 10:53
不知道这是不是你想要的

好的，谢谢前辈了，我会看下的

头狼周

据我所知有三种

波音7777

保险分很多种啊，保险丝，开口销，自锁垫片，至于保险丝单股的双股的

不想拿扳手

我只知道有几种保险，没听过保险有几种打法

kittyom

保险丝:单向保险跟双向保险，两者都要从固定端打到活动端，双向的要保证始终穿线压着绕线走，从边孔穿的话，角度是60→60→80，从对孔穿的话，角度是120→60→80，不管单股保险还是双股保险，结尾都是以80度编花，而且都只能打3~5个花开口销:有横向、纵向打法，顺序有从上到下，从左到右、从里到外三个顺序，横向打法插进去后直接左右掰开怼到旁边的孔槽里头，但是不能挨着紧固件螺纹，纵向打法也是插进去后直接上下掰开，贴合在顶面的那一边长度要小于紧固件顶端面直径，大其半径

kittyom

拆保险丝的话是先拧松再剪其穿线

烛雨

jzh17707051497 发表于 2017-9-22 07:58
保险丝:单向保险跟双向保险，两者都要从固定端打到活动端，双向的要保证始终穿线压着绕线走，从边孔穿的话 ...

了解了，多谢前辈指教

kittyom

烛雨 发表于 2017-9-23 08:40
了解了，多谢前辈指教

不客气

mtcsuperman

谢谢前辈了，我会看下的

zhaojq@139.com

B. Lockwire Installation
(1) Cut a length of the lockwire.
Make sure that the length is twice the distance between the points where the lockwire will be
attached.
(2) Put one end of the lockwire through the lockwire installation hole at the first attachment point.
(3) Pull the end of the lockwire until it is aligned with the other end.
(4) Twist the lockwire.
Make sure that there are 9 to 12 twists per inch between the attachment points.
(5) Put one end of the lockwire through the lockwire installation hole at the next attachment point.
Make sure that the lockwire is in the position that will keep the component from disengaging if the
component becomes loose.
(6) Twist the lockwire.
Make sure that there are 9 to 12 twists per inch between the attachment points.
(7) Repeat steps Step (5) through Step (6) for each attachment point.
(8) Twist the ends of the wire.
Make sure that there are 3 to 6 twists past the last attachment point.
(9) Bend the end of the lockwire over.